Command:

show ipx interface

Mode:

Router#


Syntax:

show ipx interface [type number] [brief]


Syntax Description:

type

(Optional) Interface type. It can be one of the following types: asynchronous, dialer, Ethernet (IEEE 802.3), FDDI, loopback, null, serial, Token Ring, or tunnel.

number

(Optional) Interface number

brief Brief summary of IPX interface status and configuration


Command Description:

To display the status of the IPX interfaces configured in the Cisco IOS software and the parameters configured on each interface, use the show ipx interface EXEC command.


Examples:

The following is a sample of output from the show ipx interface command:

Router#show ipx interface fastethernet 0/1


FastEthernet0/1 is up, line protocol is up
  IPX address is C03.0000.0c05.6030, NOVELL-ETHER [up] line-up, RIPPQ: 0, SAPPQ : 0
  Delay of this Novell network, in ticks is 1
  IPXWAN processing not enabled on this interface.
  IPX SAP update interval is 1 minute(s)
  IPX type 20 propagation packet forwarding is disabled
  Outgoing access list is not set
  IPX Helper access list is not set
  SAP Input filter list is not set
  SAP Output filter list is not set
  SAP Router filter list is not set
  SAP GNS output filter list is not set
  Input filter list is not set
  Output filter list is not set
  Router filter list is not set
  Netbios Input host access list is not set
  Netbios Input bytes access list is not set
  Netbios Output host access list is not set
  Netbios Output bytes access list is not set
  Update time is 60 seconds
  IPX accounting is enabled
  IPX fast switching is configured (enabled)
  IPX SSE switching is disabled
 

The following is a sample of output from the show ipx interface command when NLSP is enabled:

Router#show ipx interface fastethernet 1

  FastEthernet0 is up, line protocol is up
  IPX address is E001.0000.0c02.8cf9, SAP [up] line-up, RIPPQ: 0, SAPPQ : 0
  Delay of this IPX network, in ticks is 1 throughput 0 link delay 0
  IPXWAN processing not enabled on this interface.
  IPX SAP update interval is 1 minute(s)
  IPX type 20 propagation packet forwarding is disabled
  Outgoing access list is not set
  IPX Helper access list is not set
  SAP Input filter list is not set
  SAP Output filter list is not set
  SAP Router filter list is not set
  SAP GNS output filter list is not set
  Input filter list is not set
  Output filter list is not set
  Router filter list is not set
  Netbios Input host access list is not set
  Netbios Input bytes access list is not set
  Netbios Output host access list is not set
  Netbios Output bytes access list is not set
  Update time is 60 seconds
  IPX accounting is enabled
  IPX fast switching is configured (enabled)
  IPX SSE switching is disabled
  IPX NLSP is running on primary network E001
  RIP compatibility mode is AUTO (OFF)
  SAP compatibility mode is AUTO (OFF)
  Level 1 Hello interval 20 sec
  Level 1 Designated Router Hello interval 10 sec
  Level 1 CSNP interval 30 sec
  Level 1 LSP retransmit interval 5 sec, LSP (pacing) interval 1000 mSec
  Level 1 adjacency count is 1
  Level 1 circuit ID is 0000.0C02.8CF9.02
 

The table below describes the fields shown in the display.

Table: show ipx interface Field Descriptions

Field Description

Ethernet1 is ..., line protocol is ...

Type of interface and whether it is currently active and inserted into the network (up) or inactive and not inserted (down)

IPX address is ...

Network and node address of the local router interface, followed by the type of encapsulation configured on the interface and the interface's status. Refer to the ipx network command for a list of possible values.

NOVELL-ETHER

Type of encapsulation being used on the interface, if any

[up] line-up

Indicates whether IPX routing is enabled or disabled on the interface. The "line-up" indicates that IPX routing has been enabled with the ipx routing command. The "line-down" indicates that it is not enabled. The word in square brackets provides more detail about the status of IPX routing when it is in the process of being enabled or disabled.

RIPPQ

Number of packets in the RIP queue

SAPPQ

Number of packets in the SAP queue

Secondary address is ...

Address of a secondary network configured on this interface, if any, followed by the type of encapsulation configured on the interface and the interface's status. Refer to the ipx routing command for a list of possible values. This line is displayed only if you have configured a secondary address with the ipx routing command.

Delay of this IPX network, in ticks, ...

Value of the ticks field (configured with the ipx delay command)

throughput

Throughput of the interface (configured with the ipx spx-idle-time interface configuration command)

link delay

Link delay of the interface (configured with the ipx link-delay interface configuration command)

IPXWAN processing...

Indicates whether IPXWAN processing has been enabled on this interface with the ipx ipxwan command

IPX SAP update interval

Indicates the frequency of outgoing SAP updates (configured with the ipx update interval command)

IPX type 20 propagation packet forwarding...

Indicates whether forwarding of IPX type 20 propagation packets (used by NetBIOS) is enabled or disabled on this interface, as configured with the ipx type-20-propagation command.

Outgoing access list

Indicates whether an access list has been enabled with the
ipx access-group command

IPX Helper access list

Number of the broadcast helper list applied to the interface with the ipx helper-list command

SAP Input filter list

Number of the input SAP filter applied to the interface with the ipx input-sap-filter command

SAP Output filter list

Number of the output SAP filter applied to the interface with the ipx output-sap-filter command.

SAP Router filter list

Number of the router SAP filter applied to the interface with the ipx router-sap-filter command

SAP GNS output filter list

Number of the Get Nearest Server (GNS) response filter applied to the interface with the ipx output-gns-filter command

Input filter list

Number of the input filter applied to the interface with the
ipx input-network-filter command

Output filter list

Number of the output filter applied to the interface with the
ipx output-network-filter command

Router filter list

Number of the router entry filter applied to the interface with the ipx router-filter command

Netbios Input host access list

Name of the IPX NetBIOS input host filter applied to the interface with the ipx netbios input-access-filter host command

Netbios Input bytes access list

Name of the IPX NetBIOS input bytes filter applied to the interface with the ipx netbios input-access-filter bytes command

Netbios Output host access list

Name of the IPX NetBIOS output host filter applied to the interface with the ipx netbios input-access-filter host command

Netbios Output bytes access list

Name of the IPX NetBIOS output bytes filter applied to the interface with the ipx netbios input-access-filter bytes command

Update time

How often the Cisco IOS software sends RIP updates, as configured with the ipx update sap-after-rip command

Watchdog spoofing ...

Indicates whether watchdog spoofing is enabled of disabled for this interface, as configured with the ipx watchdog-spoof command. This information is displayed only on serial interfaces.

IPX accounting

Indicates whether IPX accounting has been enabled with the ipx accounting command

IPX fast switching
IPX autonomous switching

Indicates whether IPX fast switching is enabled (default) or disabled for this interface, as configured with ipx route-cache command. (If IPX autonomous switching is enabled, it is configured with the ipx route-cache cbus command.)

IPX SSE switching

Indicates whether IPX SSE switching is enabled for this interface, as configured with the ipx route-cache sse command

IPX NLSP is running on primary network E001

Indicates that NLSP is running and the number of the primary IPX network on which it is running

RIP compatibility mode

State of RIP compatibility (configured by the ipx nlsp rip interface configuration command)

SAP compatibility mode

State of SAP compatibility (configured by the ipx nlsp sap interface configuration command)

Level 1 Hello interval

Interval between transmission of hello packets for nondesignated routers (configured by the ipx nlsp hello-interval interface configuration command)

Level 1 Designated Router Hello interval

Interval between transmission of hello packets for designated routers (configured by the ipx nlsp hello-interval interface configuration command)

Level 1 CSNP interval

CSNP interval (as configured by the ipx nlsp csnp-interval interface configuration command)

Level 1 LSP retransmit interval

LSP retransmission interval (as configured by the ipx nlsp retransmit-interval interface configuration command)

LSP (pacing) interval

LSP transmission interval (as configured by the ipx nlsp lsp-interval interface configuration command)

Level 1 adjacency count

Number of Level 1 adjacencies in the adjacency database

Level 1 circuit ID

System ID and pseudonode number of the designated router. In this example, 0000.0C02.8CF9 is the system ID, and 02 is the pseudonode number.

 

Misconceptions:
None

Related commands:
access-list (IPX standard)
access-list (IPX extended)
ipx access-list
ipx network
ipx routing

� Cisco Systems, Inc. 2001, 2002, 2003
World Wide Education

Converted from CHM to HTML with chm2web Pro 2.85 (unicode)